Fiber Status
| Optical WAN Operational Status | Down |
|---|---|
| Fiber Module | Unavailable |
| Last Change | Unavailable |
| Link State | Down |
| Name | Unavailable |
| Connector | 0 |
| Transceiver | Unavailable |
| Encoding | 0 |
| BR Nominal | 0 |
| Br Min | 0 |
| Br Max | 0 |
| Rate ID | 0 |
| Wave Length | 0 |
| Tx Disable State | 0 |
| RS1 State | 0 |
| Rate Select State | 0 |
| Tx Fault State | 0 |
| Rx LOS State | 0 |
| Data Ready Bar State | 0 |
| Length SMF-km | 0 |
| Length SMF | 0 |
| Length 50uM | 0 |
| Length 62dot5uM | 0 |
| Length OM3 | 0 |
| Vendor Name | Unavailable |
| Vendor OUI | Unavailable |
| Vendor PN | Unavailable |
| Vendor Rev | Unavailable |
| Vendor SN | Unavailable |
| Vendor Date Code | Unavailable |
| OPT Cooled Trans | uncooled transceiver |
| OPT Powerlvl | 1 |
| OPT Linear Rcvr | conventional receiver |
| OPT Rate Select | 0 |
| OPT Tx Disable | 0 |
| OPT Tx Fault | 0 |
| OPT Inverted-LOS | 0 |
| OPT LOS | 0 |
| DMC Type Implemented | 0 |
| DMC Type Internal Cal | 0 |
| DMC Type External Cal | 0 |
| DMC Type Rx Avg Pwr | Modulation Amplitude method |
| EOC Alarm Implemented | 0 |
| EOC Soft Tx Disable | 0 |
| EOC Soft Tx fault | 0 |
| EOC Soft Rx LOS | 0 |
| EOC Soft Rate Select | 0 |
| SFF 8079 App Select | 0 |
| SFF 8431 Soft Rate Select | 0 |
| SFF Ver Compliance | Unavailable |
Temperature Currently 0
| Low | High | |
|---|---|---|
| Alarm | 0 (Threshold 0) | 0 (Threshold 0) |
| Warning | 0 (Threshold 0) | 0 (Threshold 0) |
Vcc Currently 0
| Low | High | |
|---|---|---|
| Alarm | 0 (Threshold 0) | 0 (Threshold 0) |
| Warning | 0 (Threshold 0) | 0 (Threshold 0) |
Tx Bias Currently 0
| Low | High | |
|---|---|---|
| Alarm | 0 (Threshold 0) | 0 (Threshold 0) |
| Warning | 0 (Threshold 0) | 0 (Threshold 0) |
Tx Power Currently 0
| Low | High | |
|---|---|---|
| Alarm | 0 (Threshold 0) | 0 (Threshold 0) |
| Warning | 0 (Threshold 0) | 0 (Threshold 0) |
Rx Power Currently 0
| Low | High | |
|---|---|---|
| Alarm | 0 (Threshold 0) | 0 (Threshold 0) |
| Warning | 0 (Threshold 0) | 0 (Threshold 0) |
Help
Fiber status is presented for service technicians.
Optical WAN Operational Status: When connected to a fiber source, displays whether or not the WAN is operational.Fiber Module: The type of connector detected by the device.
Last Change: Accumulated time in seconds since the optical interface entered its current state.
Link State: Up indicates link is operational.
Name: Name of the optical converter.
Connector: The code for the external optical or electrical cable connector provided as the media interface.
Transceiver: The code for electronic or optical compatibility.
Encoding: The code for the high speed serial encoding algorithm.
BR Nominal: The nominal signaling rate in 100 MBd.
Br Min: Lower bit rate margin, units of %.
Br Max: Upper bit rate margin, units of %.
Rate ID: The coded rate select identifier.
Wave Length: Laser Wavelength.
Tx Disable State: The digital state of the TX Disable input pin.
RS1 State: The digital state of SFP input pin AS(1) or RS(1).
Rate Select State: The digital state of the SFP Rate_Select input pin.
Tx Fault State: The digital state of the TX Fault output pin.
Rx LOS State: The digital state of the RX_LOS output pin.
Data Ready Bar State: Flag indicates power up and data ready.
Length SMF-km: Supported link length in kilo meters.
Length SMF: Supported link length in units of 100 meters.
Length 50uM: Supported link length for 50 micro meter OM2 fiber ( units of 10 meters).
Length 62dot5uM: Supported link length for 62.5 micro meter OM1 fiber (units of 10 meters).
Length OM3: Supported link length for 50 micro meter OM3 fiber.(units of 10 meters).
Vendor Name: SFP vendor name.
Vendor OUI: IEEE company ID for the SFP vendor.
Vendor PN: SFP module vendor part number.
Vendor Rev: SFP module revision level for the part number.
Vendor SN: SFP module serial number from vendor.
Vendor Date code: In format <yymmddxx> where xx is vendor specific and may be blank.
OPT Cooled Trans: The transceiver indication of cooled or uncooled.
OPT Powerlvl: Power Level Operation of either 1 or 2.
OPT Linear Rcvr: Indicates if Receiver is a conventional or linear receiver.
OPT Rate Select: Indicates if Rate Select is implemented. 1 = implemented. 0 = not implemented.
OPT Tx Disable: Ability to disable the serial output. 1 = implemented. 0 = not implemented.
OPT Tx Fault: TX_FAULT signal is implemented. 1 = implemented. 0 = not implemented.
OPT Inverted-LOS: Also known as 'signal detect'. 1 = implemented. 0 = not implemented.
OPT LOS: Loss of Signal. 1 = implemented. 0 = not implemented.
DMC Type Legacy: Reserved. Always 0
DMC Type Implemented: Diag monitoring. 1 = implemented. 0 = not implemented.
DMC Type Internal Cal: Device internally calibrated.
DMC Type External Cal: Device externally calibrated.
DMC Type Ex Avg Pwr: Type of power measurement: Modulation Amplitude method or Average power method.
EOC Alarm: 1 = alarm implemented. 0 = alarm not implemented.
EOC Soft Tx Disable: TX_DISABLE control and monitoring: 1 = implemented. 0 = not implemented.
EOC Soft Tx fault: TX_FAULT monitoring: 1 = implemented. 0 = not implemented.
EOC Soft Rx LOS: RX_LOS monitoring: 1 = implemented. 0 = not implemented.
EOC Soft Rate Select: Soft RATE_SELECT control and monitoring: 1 = implemented. 0 = not implemented.
SFF 8079 App Select: Application select implemented from the standard SFF 8079: 1 = implemented (partial). 0 = not implemented.
SFF 8431 Rate Select: Rate select implemented from standard 8431: 1 = implement. 0 = not implemented.
SFF Ver Compliance: Reference 3.12 table in SFF 8472. Rev 9.3 or rev 9.5.
Temperature: The temperature in degrees celsius. System is stable when current value is between low and high warning/alarm thresholds.
Vcc: Voltage in Volts/10,000. System is stable when current value is between low and high warning/alarm thresholds.
Tx Bias: Tx Bias in amperes/500,000. System is stable when current value is between low and high warning/alarm thresholds.
Tx Power: Power in one-tenth of a dBm. System is stable when current value is between low and high warning/alarm thresholds.
Rx Power: Power in one-tenth of a dBm. System is stable when current value is between low and high warning/alarm thresholds.